I have an old LaView LV-N9508Q8E network video recorder. I wanted better monitoring, so I tried to enable SNMP. The firmware does not support it, and LaView is gone the way of the world, but it looks like this is a re-badged HIKVision DS-7608NXI-K1/8P. Maybe I can upgrade the firmware to a non-LaView firmware?
The background is that LaView is non-existant any longer. However,
So, downloading that firmware should, in theory, allow me to drop in the latest HIKVision firmware that might enable SNMP. It might also enable better motion detection alerting (send it through an Apache web service?).
This was a fun trip. I tried upgrading to a HIKVISION firmware first via the web browser, and also from the command line. This lead me to setting up a new tftp server, dropping the 3.4.112 version of firmware into the tftp root directory as "digicap.dav", and building a 1.5mm, 4-pin JST header for the serial output. A "screen /dev/DEVICENAME 115200" gave me the console.
After reading up a lot on the "upgrades", the instructions looked fairly simple. However, once I got in there (you have to hit the control-u often and quickly while you are turning the device on, FYI), you might get launched into an upgrade script automatically.
I didn't. Instead, I got an "HKVS $" prompt.
U-Boot 2010.06-svn17334 (Sep 15 2017 - 19:37:08)
Hit ctrl+u to stop autoboot: 0
HKVS $Instead, I had to run a series of commands that appear very "hacky". As in SQL database drop-table hacky, like adding a semi colon and letting the parser run another command that you couldn't otherwise get to. For example :
setenv ';setenv ipaddr 192.168.128.8;saveenv'
setenv ';setenv serverip 192.168.128.6;saveenv'These will set IP addresses, then save the environment variables for the next session (yeah, you have to save between sessions). Essentially, the output looked like :
U-Boot 2010.06-svn17334 (Sep 15 2017 - 19:37:08)
Hit ctrl+u to stop autoboot: 0
HKVS $ setenv ';setenv ipaddr 192.168.128.8;saveenv'
Saving Environment to SPI Flash...
Warning: Erase size 0x00001000 smaller than one erase block 0x00010000
Erasing 0x00010000 instead
Erasing SPI flash, offset 0x00120000 size 64K ...done
Writing to SPI flash, offset 0x00120000 size 4K ...done
HKVS $ setenv ';setenv serverip 192.168.128.6;saveenv'
Saving Environment to SPI Flash...
Warning: Erase size 0x00001000 smaller than one erase block 0x00010000
Erasing 0x00010000 instead
Erasing SPI flash, offset 0x00120000 size 64K ...done
Writing to SPI flash, offset 0x00120000 size 4K ...done
HKVS $Now, I could start the upgrade :
setenv ';upgrade'And (after a few minutes), I was running native HikVISION firmware! I then upgraded to 4.30.097, and did a full factory reset (gotta clean 'er up, eh?).
After it came back online, no cameras were coming online. Turns out, I have to do a camera reset on every one of those (which might prove a little difficult since they are all PoE).
So, after a quick factory reset... nothing. I am losing interest here, as it still doesn't work in the browser, and in Windows, it prompted for a "plug-in". But, it did have an option to enable ssh, and if you do that, you can shell as "root" to the device using your "admin" password. It is a very limited shell, but allows you to run "dmesg", which will tell you exactly what is on this set of hardware :
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.18.20 (root@CI-Backend-Slave-65-115) (gcc version 4.9.4 20150629 (prerelease) (Hisilicon_v500_20170922) ) #2 SMP Wed Dec 14 17:22:34 CST 2022
[ 0.000000] setup for rdinit= is not allowed, disable it!
[ 0.000000] setup for load_ramdisk= is not allowed, disable it!
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: HIKVISON K74 Platform Board
[ 0.000000] Uboot is not supported safe version:V0
[ 0.000000] Command [ipaddr] is not supported, please check cmdline.
[ 0.000000] Command [192.168.128.8] is not supported, please check cmdline.
[ 0.000000] Command [serverip] is not supported, please check cmdline.
[ 0.000000] Command [192.168.128.6] is not supported, please check cmdline.
[ 0.000000] Command [serverip] is not supported, please check cmdline.
[ 0.000000] Command [192.168.128.6] is not supported, please check cmdline.
[ 0.000000] Command [bootpart=] is not supported, please check cmdline.
[ 0.000000] HIKBASE version ##78762[kernel:74730] v2.1.0 build 2022-12-14
[ 0.000000] HIKBSP svnpath: baseline/branches/trunk-v2.3.2/hikbsp-v2@85692
[ 0.000000] request_module: runaway loop modprobe fs-proc
[ 0.000000] Ignoring unrecognised tag 0x54410001
[ 0.000000] Ignoring unrecognised tag 0x54410009
[ 0.000000] cpldinfo offset[0x100000], size[0x100].
[ 0.000000] Ignoring unrecognised tag 0x484b0002
[ 0.000000] Ignoring unrecognised tag 0x484b0004
[ 0.000000] Ignoring unrecognised tag 0x484b0005
[ 0.000000] CMEM[10]: 0x83000000+0x00020000 reserve ok!
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 163840
[ 0.000000] free_area_init_node: node 0, pgdat c07eb180, node_mem_map e7af7000
[ 0.000000] Normal zone: 1280 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 163840 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 9 pages/cpu @e7ad9000 s6080 r8192 d22592 u36864
[ 0.000000] pcpu-alloc: s6080 r8192 d22592 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 162560
[ 0.000000] Kernel command line: mem=640M console=ttyS0,115200n8 noinitrd ip=ADDR:ADDR:MULTICAST:MASK:Hik-eth:eth0:none
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 640796K/655360K available (4770K kernel code, 207K rwdata, 1468K rodata, 1632K init, 272K bss, 14564K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xe8800000 - 0xff000000 ( 360 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe8000000 ( 640 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc061fc3c (6240 kB)
[ 0.000000] .init : 0xc0620000 - 0xc07b8000 (1632 kB)
[ 0.000000] .data : 0xc07b8000 - 0xc07ebe60 ( 208 kB)
[ 0.000000] .bss : 0xc07ebe60 - 0xc083009c ( 273 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000011] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns
[ 0.000195] Console: colour dummy device 80x30
[ 0.000210] Calibrating delay loop... 2596.86 BogoMIPS (lpj=12984320)
[ 0.060049] pid_max: default: 32768 minimum: 301
[ 0.060145] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060154] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060644] CPU: Testing write buffer coherency: ok
[ 0.060875] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.061004] Setting up static identity map for 0x8048d698 - 0x8048d6f0
[ 0.062109] CPU1: Booted secondary processor
[ 0.120070] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.120134] Brought up 2 CPUs
[ 0.120147] SMP: Total of 2 processors activated (5187.17 BogoMIPS).
[ 0.120152] CPU: All CPU(s) started in SVC mode.
[ 0.121697] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.121974] pinctrl core: initialized pinctrl subsystem
[ 0.122136] regulator-dummy: no parameters
[ 0.123688] NET: Registered protocol family 16
[ 0.123900] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.123915] Find the board(K74).
[ 0.123921] Current board is PCB[0x80315], BOARD[0x4600]
[ 0.126853] Serial: AMBA PL011 UART driver
[ 0.126939] 12080000.uart: ttyS0 at MMIO 0x12080000 (irq = 38, base_baud = 0) is a PL011 rev2
[ 0.127107] console [ttyS0] enabled
[ 0.127280] uart-pl011 12090000.uart: aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable.
[ 0.127296] 12090000.uart: ttyS1 at MMIO 0x12090000 (irq = 39, base_baud = 0) is a PL011 rev2
[ 0.127428] uart-pl011 120a0000.uart: aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable.
[ 0.127442] 120a0000.uart: ttyS2 at MMIO 0x120a0000 (irq = 40, base_baud = 0) is a PL011 rev2
[ 0.161021] SCSI subsystem initialized
[ 0.161150] libata version 3.00 loaded.
[ 0.161353] usbcore: registered new interface driver usbfs
[ 0.161404] usbcore: registered new interface driver hub
[ 0.161443] usbcore: registered new device driver usb
[ 0.162097] Switched to clocksource timer00
[ 0.165750] NET: Registered protocol family 2
[ 0.166268] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.166333] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.166421] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.166473] TCP: reno registered
[ 0.166484] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166525] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166698] NET: Registered protocol family 1
[ 0.166947] RPC: Registered named UNIX socket transport module.
[ 0.166956] RPC: Registered udp transport module.
[ 0.166960] RPC: Registered tcp transport module.
[ 0.166965] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.715919] persistent_ram: uncorrectable error in header
[ 0.716011] persistent_ram: uncorrectable error in header
[ 0.716097] persistent_ram: uncorrectable error in header
[ 0.716357] console [pstore-1] enabled
[ 0.716448] pstore: Registered ramoops as persistent store backend
[ 0.716455] ramoops: attached 0x20000@0x83000000, ecc: 16/0
[ 0.716944] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.723834] NFS: Registering the id_resolver key type
[ 0.723886] Key type id_resolver registered
[ 0.723891] Key type id_legacy registered
[ 0.723948] ntfs: driver 2.1.31 [Flags: R/W].
[ 0.724231] fuse init (API version 7.23)
[ 0.724571] yaffs: yaffs built Installing.
[ 0.724599] msgmni has been set to 1251
[ 0.725748] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.725764] io scheduler noop registered (default)
[ 0.753427] pinctrl-single 120f0000.pinmux: 234 pins at pa fe4f0000 size 936
[ 0.757142] brd: module loaded
[ 0.757521] Loading iSCSI transport class v2.0-870.
[ 0.757893] iscsi: registered transport (tcp)
[ 0.870145] ahci 11010000.sata: SSS flag set, parallel bus scan disabled
[ 0.870175] ahci 11010000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.870187] ahci 11010000.sata: flags: ncq sntf stag pm led clo only pmp fbs slum part ccc sxs boh
[ 0.871027] scsi host0: ahci_platform
[ 0.871348] scsi host1: ahci_platform
[ 0.871517] ata1: SATA max UDMA/133 mmio [mem 0x11010000-0x11010fff] port 0x100 irq 49
[ 0.871524] ata2: SATA max UDMA/133 mmio [mem 0x11010000-0x11010fff] port 0x180 irq 49
[ 0.872042] hisi-sfc hisi_spi_nor.0: w25x16/s25fl016k (2048 Kbytes)
[ 0.872194] SPI Nand ID Table Version 2.7
[ 0.873269] SPI Nand(cs 1) ID: 0x2c 0x14
[ 0.873293] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x14
[ 0.873298] nand: Micron MT29F1G01ABA
[ 0.873303] nand: 128MiB, SLC, page size: 2048
[ 0.873308] Nand(Auto): OOB:128B ECC:24bit/1k
[ 0.873321] nand: ECC provided by Flash Memory Controller
[ 1.050156] libphy: hisi_gemac_mii_bus: probed
[ 1.300158] libphy: hisi_gemac_mii_bus: probed
[ 1.940128] libphy: hisi_own_mii_bus: probed
[ 2.140170] hi_gmac_v200 100a0000.ethernet (unnamed net_device) (uninitialized): using random MAC address 2e:26:e5:41:5d:55
[ 2.330143] attached PHY 1 to driver Generic PHY, PHY_ID=0x600d84a2
[ 2.330473] Higmac dma_sg_phy: 0xa5140000
[ 2.330913] ETH: rgmii, phy_addr=1
[ 2.530171] hi_gmac_v200 100a1000.ethernet (unnamed net_device) (uninitialized): using random MAC address a6:c8:a3:d9:d5:8d
[ 2.610159] attached PHY 8 to driver Generic PHY, PHY_ID=0x8
[ 2.610463] Higmac dma_sg_phy: 0xa5280000
[ 2.610892] ETH: mii, phy_addr=8
[ 2.611040] PPP generic driver version 2.4.2
[ 2.611140] PPP BSD Compression module registered
[ 2.611149] PPP Deflate Compression module registered
[ 2.611167] PPP MPPE Compression module registered
[ 2.611180] NET: Registered protocol family 24
[ 2.611382] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.611393] ehci-platform: EHCI generic platform driver
[ 2.611480] ehci-platform 10040000.ehci: EHCI Host Controller
[ 2.611504] ehci-platform 10040000.ehci: new USB bus registered, assigned bus number 1
[ 2.611578] ehci-platform 10040000.ehci: irq 51, io mem 0x10040000
[ 2.630171] ehci-platform 10040000.ehci: USB 2.0 started, EHCI 1.00
[ 2.630686] hub 1-0:1.0: USB hub found
[ 2.630730] hub 1-0:1.0: 2 ports detected
[ 2.631032] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.631044] ohci-platform: OHCI generic platform driver
[ 2.631132] ohci-platform 10030000.ohci: Generic Platform OHCI controller
[ 2.631160] ohci-platform 10030000.ohci: new USB bus registered, assigned bus number 2
[ 2.631212] ohci-platform 10030000.ohci: irq 50, io mem 0x10030000
[ 2.694630] hub 2-0:1.0: USB hub found
[ 2.694663] hub 2-0:1.0: 2 ports detected
[ 2.695034] usbcore: registered new interface driver usb-storage
[ 2.695145] usbcore: registered new interface driver usbserial
[ 2.695183] usbcore: registered new interface driver mos7840
[ 2.695217] usbserial: USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[ 2.695358] mousedev: PS/2 mouse device common for all mice
[ 2.695377] i2c /dev entries driver
[ 2.695658] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.695826] usbcore: registered new interface driver usbhid
[ 2.695831] usbhid: USB HID core driver
[ 2.696004] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.696060] TCP: cubic registered
[ 2.696588] NET: Registered protocol family 10
[ 2.697499] sit: IPv6 over IPv4 tunneling driver
[ 2.698002] NET: Registered protocol family 17
[ 2.698063] 8021q: 802.1Q VLAN Support v1.8
[ 2.698113] Key type dns_resolver registered
[ 2.698124] Key type ceph registered
[ 2.698536] libceph: loaded (mon/osd proto 15/24)
[ 2.698620] Registering SWP/SWPB emulation handler
[ 2.698690] HIKBASERD: Loading 237KiB [2 disks] into "/home/hikbase.image"... done.
[ 2.700879] /data/jenkins/workspace/Backend-BSP-CCI/8505/opensource/kernel/linux-3.18.20/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.702324] Freeing unused kernel memory: 1632K (c0620000 - c07b8000)
[ 2.703694] init(1) called reboot syscall, cmd: 0x0.
[ 3.170247] usb 2-2: new low-speed USB device number 2 using ohci-platform
[ 3.402261] input: DaKai 2.4G RX as /devices/soc/10030000.ohci/usb2/2-2/2-2:1.0/0003:0E8F:00A8.0001/input/input0
[ 3.402447] hid-generic 0003:0E8F:00A8.0001: input,hidraw0: USB HID v1.10 Keyboard [DaKai 2.4G RX] on usb-10030000.ohci-2/input0
[ 3.412386] input: DaKai 2.4G RX as /devices/soc/10030000.ohci/usb2/2-2/2-2:1.1/0003:0E8F:00A8.0002/input/input1
[ 3.412735] hid-generic 0003:0E8F:00A8.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [DaKai 2.4G RX] on usb-10030000.ohci-2/input1
[ 3.578060] hik_hal: module license 'HIKLICENSE' taints kernel.
[ 3.578077] Disabling lock debugging due to kernel taint
[ 3.579406] [HKBSP]HIK-BSP version #85692[kernel:74730, hikbase:78762] v2.3.2 build 2022-12-14
[ 3.579478] [HKBSP]start parsing ARGS: 'mem=640M console=ttyS0,115200n8 noinitrd ip=ADDR:TFTPADDR:MULTICAST:MASK:Hik-eth:eth0:none '
[ 3.579491] [HKBSP]Ignoring unrecognised tag 0x54410001
[ 3.579496] [HKBSP]Ignoring unrecognised tag 0x54410009
[ 3.579502] [HKBSP]cpldinfo offset[0x100000], size[0x100].
[ 3.579509] [HKBSP]bootparam offset[0x110000], size[0x200].
[ 3.579516] [HKBSP]envinfo offset[0x120000], size[0x1000].
[ 3.579521] [HKBSP]Ignoring unrecognised tag 0x484b0005
[ 3.583783] [HKBSP]Find the platform(K74).
[ 3.584219] Creating 4 MTD partitions on "hinand":
[ 3.584234] 0x000000c00000-0x000003c00000 : "flash_sys0"
[ 3.630457] 0x000003c00000-0x000006c00000 : "flash_sys1"
[ 3.676558] 0x000006c00000-0x000007c00000 : "data_config"
[ 3.692201] 0x000007c00000-0x000008000000 : "rev"
[ 3.696832] SSC board name is DS_80315
[ 3.890329] hik_rtc hik_rtc.0: rtc core: registered hik_rtc as rtc0
[ 4.425514] random: sleep urandom read with 13 bits of entropy available
[ 5.497395] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.575463] UBI: attaching mtd0 to ubi0
[ 5.700127] UBI: scanning is finished
[ 5.703994] UBI: attached mtd0 (name "flash_sys0", size 48 MiB) to ubi0
[ 5.704006] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.704012] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.704017] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.704022] UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
[ 5.704027] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.704034] UBI: max/mean erase counter: 7/4, WL threshold: 4096, image sequence number: 131538258
[ 5.704039] UBI: available PEBs: 0, total reserved PEBs: 384, PEBs reserved for bad PEB handling: 10
[ 5.704379] UBI: background thread "ubi_bgt0d" started, PID 208
[ 5.710744] UBIFS: background thread "ubifs_bgt0_0" started, PID 211
[ 5.723745] UBIFS: recovery needed
[ 5.763013] UBIFS: recovery completed
[ 5.763030] UBIFS: mounted UBI device 0, volume 0, name "sys0"
[ 5.763038] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.763045] UBIFS: FS size: 45711360 bytes (43 MiB, 360 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs)
[ 5.763050] UBIFS: reserved for root: 2159060 bytes (2108 KiB)
[ 5.763059] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 30A6A621-DCD0-4036-B240-374BCE3FCD58, small LPT model
[ 5.769545] UBI: attaching mtd1 to ubi1
[ 5.894140] UBI: scanning is finished
[ 5.897971] UBI: attached mtd1 (name "flash_sys1", size 48 MiB) to ubi1
[ 5.897983] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.897989] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.897994] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.897999] UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
[ 5.898004] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.898011] UBI: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1105190896
[ 5.898016] UBI: available PEBs: 0, total reserved PEBs: 384, PEBs reserved for bad PEB handling: 10
[ 5.898340] UBI: background thread "ubi_bgt1d" started, PID 214
[ 5.904655] UBIFS: background thread "ubifs_bgt1_0" started, PID 217
[ 5.917683] UBIFS: recovery needed
[ 5.961355] UBIFS: recovery completed
[ 5.961374] UBIFS: mounted UBI device 1, volume 0, name "sys1"
[ 5.961381] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.961388] UBIFS: FS size: 45711360 bytes (43 MiB, 360 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs)
[ 5.961394] UBIFS: reserved for root: 2159060 bytes (2108 KiB)
[ 5.961402] UBIFS: media format: w4/r0 (latest is w4/r0), UUID BC3CD3A0-B8EF-4E08-A7F6-41234BE47A75, small LPT model
[ 5.967882] UBI: attaching mtd2 to ubi2
[ 6.009894] UBI: scanning is finished
[ 6.013551] UBI: attached mtd2 (name "data_config", size 16 MiB) to ubi2
[ 6.013564] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.013570] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.013575] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.013580] UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
[ 6.013585] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 6.013592] UBI: max/mean erase counter: 13/8, WL threshold: 4096, image sequence number: 2086548976
[ 6.013597] UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 10
[ 6.013924] UBI: background thread "ubi_bgt2d" started, PID 220
[ 6.020337] UBIFS: background thread "ubifs_bgt2_0" started, PID 223
[ 6.033262] UBIFS: recovery needed
[ 6.083720] UBIFS: recovery completed
[ 6.083740] UBIFS: mounted UBI device 2, volume 0, name "cfg"
[ 6.083747] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.083754] UBIFS: FS size: 13205504 bytes (12 MiB, 104 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 6.083760] UBIFS: reserved for root: 623728 bytes (609 KiB)
[ 6.083768] UBIFS: media format: w4/r0 (latest is w4/r0), UUID FCFF6689-D905-4BFD-8A33-BC2290044107, small LPT model
[ 6.132001] [HKBSP] selftests...
[ 6.132154] Finish!
[ 8.556393] hi_gmac_v200 100a0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 8.565253] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.560507] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 11.757855] ata1.00: ATA-9: WDC WD20PURZ-85GU6Y0, 80.00A80, max UDMA/133
[ 11.757871] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.758462] ata1.00: configured for UDMA/133
[ 11.758784] scsi 0:0:0:0: Direct-Access ATA WDC WD20PURZ-85G 0A80 PQ: 0 ANSI: 5
[ 11.760287] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 11.760301] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 11.762210] sd 0:0:0:0: [sda] Write Protect is off
[ 11.762227] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.762356] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.791200] sda: unknown partition table
[ 11.792271] sd 0:0:0:0: [sda] Attached SCSI disk
[ 12.112617] ata2: SATA link down (SStatus 0 SControl 310)
[ 22.888404] Module himedia: init ok
[ 22.888417] Hisilicon Media Memory Zone Manager
[ 22.888507] hi_osal 1.0 init success!
[ 22.896292] load base.ko ... OK!
[ 22.900178] load sys.ko ...OK!
[ 22.906087] load vdec.ko ....OK!
[ 22.915707] load vdh firmware.ko OK
[ 22.919724] load jpegd.ko ....OK!
[ 22.925578] load tde.ko ...OK!
[ 22.931037] load region.ko ....OK!
[ 22.941232] load vgs.ko ...OK!
[ 22.949213] load vpss.ko ...OK!
[ 22.959877] load vou.ko OK!
[ 23.017070] load hifb.ko OK!
[ 23.024770] load hdmi.ko OK!
[ 23.029631] load rc.ko ...OK!
[ 23.038915] load venc.ko ...OK!
[ 23.042452] load chnl.ko ...OK!
[ 23.046324] load vedu.ko ...OK!
[ 23.051493] load h264e.ko ...OK!
[ 23.056613] load h265e.ko ...OK!
[ 23.061200] load jpege.ko ...OK!
[ 23.067550] load vda.ko ....OK!
[ 23.074297] load ive.ko ... OK!
[ 23.078952] Load hi_cipher.ko success.
[ 23.355131] regIdx 0x0 value 0x21
[... SNIP - there were a whole lot of these "regIdx" lines ...]
[ 23.512914] regIdx 0xfe value 0x10ec
[ 23.512918] *** rt5616 driver init successful! ***
[ 23.516685] load aio.ko OK!
[ 23.521750] load ai.ko OK!
[ 23.527017] load ao.ko OK!
[ 23.532006] load aenc.ko OK!
[ 23.536248] load adec.ko OK!
[ 23.568995] vca encrypt ready!vca_encrypt_major = 246
[ 23.581186] nf_conntrack version 0.5.0 (10037 buckets, 40148 max)
[ 23.635790] iscsid (386): /proc/386/oom_adj is deprecated, please use /proc/386/oom_score_adj instead.
[ 24.243631] hdmi detect retry_times : 0
[ 24.676135] start.sh (230): drop_caches: 3
[ 25.250968] hdmi detect retry_times : 1
[ 26.261000] hdmi detect retry_times : 2
[ 27.271801] hdmi detect retry_times : 0
[ 28.283110] hdmi detect retry_times : 1
[ 29.293141] hdmi detect retry_times : 2
[ 31.444024] hdmi detect retry_times : 0
[ 32.451203] hdmi detect retry_times : 1
[ 33.461234] hdmi detect retry_times : 2
[ 34.471286] hdmi detect retry_times : 0
[ 35.483379] hdmi detect retry_times : 1
[ 36.493412] hdmi detect retry_times : 2
[ 37.533550] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.535794] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 37.537468] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 37.631420] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 37.797439] hi_gmac_v200 100a1000.ethernet eth1: Link is Up - 100Mbps/Full - flow control off
[ 37.809626] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 42.217125] [HKBSP][hik_uenv hik_uenv.0][HIKUENV]attemp to create a null passwd!!!
[ 43.222014] [HKBSP][hik_uenv hik_uenv.0][HIKUENV]uboot_env_list_update set bootargs failed -17
[ 43.381698] hi_gmac_v200 100a0000.ethernet eth0: Link is Down
[ 45.517725] hi_gmac_v200 100a0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 47.233706] vca_encrypt_dbg: vca_encrypt_ioctl: CMD = 0x90
[ 47.233720] vca_encrypt_dbg: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[ 47.233725] vca_encrypt_dbg: before:chip id = 0x0
[ 47.233731] vca_encrypt_dbg: after:chip id = 0xcc3a6b18
[ 49.983829] sched: RT throttling activated
[ 163.556621] [HKBSP][hik_uenv hik_uenv.0][HIKUENV]uboot_env_list_update set passwd failed -17
[ 1259.955968] recordSysStatIn (642): drop_caches: 3
[... SNIP - a lot of drop_caches messages ...]
[51666.442642] recordSysStatIn (642): drop_caches: 3
[52865.784607] warning: process `taskStartSntpCl' used the deprecated sysctl system call with 1.40.
[52866.611454] recordSysStatIn (642): drop_caches: 3
[58549.985638] hi_gmac_v200 100a0000.ethernet eth0: Link is Down
[58554.239680] hi_gmac_v200 100a0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[58867.434429] recordSysStatIn (642): drop_caches: 3
[... SNIP - more drop_caches messages ...]
[79270.053948] recordSysStatIn (642): drop_caches: 3
[80470.201847] recordSysStatIn (642): drop_caches: 3Wow! We have a full hardware dump! Anyway, my intent is to either enable SNMP (which this firmware version does NOT have) and/or to allow a regular browser to display the video feed without silly plug-ins. I can use RTSP to connect to my cameras and view that, but the browser still won't show it. However, this is the latest version of the software I can find that will actually load on this, so I might indeed be "stuck".
No comments:
Post a Comment